A do-it-yourself double bed is a completely feasible project for DIYers. Making a bed with your own hands allows you not only to avoid unnecessary waste, but also to embody any design idea. You can make a bed, taking into account the peculiarities of the owners and the bedroom, choose any length and width.

Similar articles:

How to determine the size of the bed?

To understand how to make a double bed yourself, you must first decide on its size. The standard length of the product is considered to be 200 cm.However, this parameter varies in the range of 190-220 cm.To determine the appropriate bed size, it is necessary to add 30 cm to the person's height.

The minimum is 160 cm. There is no upper limit, but there are standards. They make up:

1. 160 cm;
2. 180 cm;
3. 200 cm;
4. 220 cm.

To determine a comfortable width, you need to lie down, put your hands on your chest and straighten your elbows. You need to measure the distance from one elbow to the other and add 10-20 cm.

Height is another important factor. If there is a need for additional storage space, you should pay attention to a bed with drawers. However, it is never low due to design features. Height can be:

• small, 20-30 cm;
• medium, 40-60 cm;
• large, 70-90 cm.

You should choose the one that is comfortable to sit on. You also need to take into account the presence of diseases of the musculoskeletal system and the age of the person.

When drawing up a diagram or drawing of a berth, it is necessary to take into account all the individual characteristics of the owner.

Materials for work

The process of making a double bed is largely dependent on the choice of materials. You can make a bed from the following materials:

1. wood;
2. gland.

A wooden stock is easier to make because the process is straightforward. To make a metal bed frame, you need to have skills in working with a welding machine and, if necessary, forging.

For working with metal

To work with metal, you will need the following materials:

• corners;
• bolts and nuts;
• profile pipe;
• plate;

All elements are connected by welding.

For working with wood

Do-it-yourself wood bed can be made from the following materials:

1. laminated chipboard;
2. solid wood;
3. glued laminated timber.

The wood bed is easier to handle and you can give any pattern to the headboard or side panels (drawers).

For a pine bed, you will need the following materials:

• timber 5x5 cm, length 220 cm - 15 pcs.;
• board 200x10x2 cm - 22 pcs.;
• wood glue or PVA;
• self-tapping screws 6.5x4 cm;
• metal corners with a shelf width of 5 cm.

The frame is intended for a mattress measuring 200x160 cm.

Necessary fittings and fasteners

To make a bed with your own hands, you need to prepare fasteners and accessories. If the sleeping place is planned to be foldable, you should purchase special folding mechanisms. They can be of the following types:

1. mechanical;
2. with springs;
3. gas.

For stationary products, you need to take:

• metal corners;
• screeds;
• screws;
• self-tapping screws;
• legs if necessary;
• lamellas or metal mesh.

To make drawers, you should purchase roller mechanisms. It is better to give preference to metal products, as they are more durable than plastic ones.

Tools for the job

To do it yourself, you need to prepare the following tools:

1. Bulgarian;
2. welding machine;
3. drill with a set of drills of different diameters;
4. roulette;
5. square;
6. square file;
7. metal brush;
8. sandpaper;
9. paint brushes;
10. primer for metal surfaces;
11. paintwork.

The presence of blacksmithing equipment will allow you to create an unusual pattern for the headboard.

To make a bed out of wood, you need to prepare the following tools:

• hacksaw;
• drill;
• drills of different diameters;
• screwdriver;
• self-tapping screws;
• wood glue or PVA;
• clamps;
• square;
• screwdriver;
• tape measure and pencil;
• iron corners;
• stain;
• sandpaper;
• paint brushes.

If you plan to make a bed from solid wood, you can use special cutters to create a pattern on the headboard for the bed. The wood frame can be stained to reveal the texture of the material and make the frame more beautiful.

Self-assembly of a double bed

To make a double bed with your own hands, you must draw up a detailed drawing of the product in advance. It should display all the nuances, the method of connecting the frame elements, and decide on the fittings. The dimensions of the bed parts must be made with an accuracy of 1 cm. Otherwise, the base may turn out to be smaller than the mattress. If it turns out to be larger, the mattress will move, which will cause inconvenience when using the bed.

Frame fabrication

If you plan a construction from a bar, you first need to glue the elements in such a way that you get:

1. side panels;
2. headboard;
3. leg back.

The surface must be flat, therefore, if necessary, the tree is planed and sanded. Otherwise, the elements will not stick together well. Since the box should have a height of 15-20 cm, it is necessary to fasten 3-4 bars with a length of 220 cm. For this, the sides of the parts are abundantly greased with glue, superimposed on each other and pressed with clamps. They start only after the glue has dried. This takes 1-2 days.

Since the glued blanks are large, they must be adjusted to the parameters indicated in the drawing. You will need side drawers with a length of 220 cm, end panels of 161 cm and a central lintel of 210 cm.

Details are fixed more reliably if you use a lock connection. To do this, measure 5 cm along the edges of the side tsars on the upper bars and saw them off. It is important not to damage the center piece as it will take on the load. Then, along the edges of the end sides, measure 5 cm on the central bar and carefully remove. Now you need to connect the parts of the bed, having previously coated them with glue. The elements are compressed with clamps and left to dry completely.

You can also make a one-piece frame, the parts of which are attached to each other by bandaging. The bars are glued into a box in an already cut form. To do this, you first need to lay out the bottom row so that you get a rectangle. The lengths of the side and end sides should be 210 and 150 cm, respectively.

The first to fit are the end parts of the side panels, which are abundantly greased with glue. They are fixed with self-tapping screws. To prevent the screws from going to the side, guide holes are made with a drill with a small diameter drill. Each connection is checked with a square to maintain a 90 ° angle. The planes should also be checked, as the tree can lead to the side. The length of the beams in it should be 220 cm, and the end part - 170 cm.

The last one is the upper row, the dimensions of which correspond to the lower one. The sides are greased with glue and fixed with self-tapping screws. It is necessary to make indentations for the screw heads so that they do not protrude above the surface. The frame is left to dry for 1-2 days.

The central lintel consists of 2 glued beams 210 cm long. Before fixing, markings are made on the inside of the frame. The middle is marked, and at the bottom, in the designated places, persistent elements 15 cm long are fastened. They act as a support for the central bar. To connect from the jumper, remove 5 cm of the lower bar on each side. Fasten this element with glue and fix it with self-tapping screws.

If the bed has legs, they are installed at this stage. Bars 20-30 cm long can act as supports.

The furniture market offers a large selection of beds, but you can make this element of the interior yourself.

The article describes how to make a double bed from available materials and components. Solid wood furniture can be inexpensive.

If you are a fan of the old-fashioned way and at the same time have the skills of welding, you can make a bed for a country cottage, in a private house or in a city apartment from a profile pipe, and decorate the headboard with decorative forging elements. We will consider a more affordable and simpler option for creating bedroom furniture, and we suggest you make a wooden bed from materials that are absolutely safe for health. Below are the drawings of the simplest options that even a novice master can easily handle.

Materials and tools

You will need:

• assembly diagram;
• sheet plywood;
• PVA glue;
• wooden beam;
• slats;
• self-tapping screws (70 pieces).

You will need a pine glued beam with a flat, flawless surface, measuring 4 x 5 x 200 cm (14 pcs.). The size of the planed slats is 2 x 10 x 200 cm (20 pcs.). Before making a bed, you need to buy a sleeping mattress 160 x 200 cm, already make a base under it.

Assembling a double bed

The rectangular frame is assembled from beams. It is necessary to take three bars on each side, fasten them together in height. You will get an equilateral rectangle. If there is a concern that the mattress will not fit, it is recommended to assemble the frame with an allowance of 1 cm on each side.

2 bars with a section of 4 x 5 cm, 162 cm long (ends) and the same parts 201 cm long (sides) are laid out on the floor, coated with PVA glue. Immediately after this, a second row of bars is laid on top. Then all the parts are fixed with self-tapping screws. The crowns of the bed must not be skewed, they should turn out to be perfectly even.

At the corners, the parts are connected using metal ties. When screwing in the self-tapping screws, the glue that did not have time to grab will see through the holes to the outside, so the wood must be cleaned of its excess.

The assembled frame can be set aside, start creating an orthopedic slatted base from processed boards 2 cm thick. The slats must be reinforced with a stiffener, it should run in the center of the bed along its entire length. There should be at least 2-3 legs. It is also necessary to make 4 legs for the frame. In the future, they are installed in the corners, securely fixed with fasteners.

For a bed of boards, you need a base of slats or slats. Supports are made of wooden beams... The beam is cut into lengths corresponding to each side of the bed. The support beams are attached at the level of the second row of the frame along the entire inner perimeter. The thickness of the support element is sufficient for the thin rack-and-pinion base to sit firmly and securely on it.

It is recommended to plan the length of the slats with the expectation that a deformation gap should form between them and the frame, preventing cracking of the natural material, excluding its creaking. It is better to fix the slats at a distance of 20-30 cm from each other. The step between them should be the same, a template may come in handy. The slats are fixed with self-tapping screws, which are twisted along the edges to the base and in the center to the stiffener. After that, the homemade bed should stand for several days until the glue is completely dry.

Further, decorative processing is carried out. First, all parts are sanded with a grinder or grinder, including a coarse grain attachment. Then, with the help of fine-grained emery, a fine sanding is carried out along the wood fibers.

After sanding and polishing, they get rid of the dust formed during the processing... In the room in which work will be carried out with the paint and varnish material, it is necessary to do wet cleaning.

The furniture is covered with a wood preservative primer. On top, in 2-3 layers, a varnish is applied with a spray gun, providing a uniform coating.

You can also use a fine-bristled brush.

In the process of varnishing, the bed must be turned over, let each layer dry.

Assembling the headboard

For work, you need a sheet of thick plywood. The end result is a plywood element that is not subject to any special mechanical stress. Its strength is sufficient. You also need dense upholstery fabric, foam rubber, synthetic winterizer, furniture stapler with staples.

A rectangle of the required size is cut from the plywood sheet with a jigsaw. On top of it, a layer of foam rubber of any thickness of the same size is laid. Foam rubber can be covered with padding polyester. Then the headboard is pulled over with upholstery fabric.

The piece of fabric should extend onto the back wall by at least 15–20 cm.

When fixing the upholstery with a stapler, it is necessary to provide the fabric with a uniform tension, without creases, ugly folds on the front surface. The headboard is attached to the wall or bed frame. In the first case, the part is supplied with special loop ears. They are hung on self-tapping screws installed in the wall. If the headboard is fixed to the back of the bed, holes are made in its lower part, as in the base of the furniture. Screws are screwed into them, clamped with nuts.

According to the same scheme, it can be completed with a headboard and a single bed. Curly headboards decorated using the carriage coupler technique will look good. In this case, you will need a stencil, furniture buttons, decorative nails.

There are many types of carriage ties, if you wish, you can choose the one that will decorate the bed, emphasize the style of the room, and make it more expressive.

In the season of gardens and vacations, you want to spend more time outdoors near your favorite beds, spruce forest and river. But you have to spend time returning to the apartment under the roof of a city high-rise building, because the garden house does not have a comfortable bed , and your living room without a bedroom and a bedside bed is right next to the dining table. Do not despair!

It all depends on how and where you want to use it. A single bed is enough for your teenage child bed ... If you are a large physique, then a comfortable sleep will come only on the "lorry".

Are you married? So, you need a double bed made of solid wood.

If there is enough space, then equip a pull-out bed under the podium, and on top place a cozy seating area with a coffee table, to which stairs lead. In a small room, where every square meter is valuable, build bed on the podium.

Build in drawers to store bedding, clothes and other items.

For bedding, place a tall, narrow drawer with a top hinged lid at the head of the bed. It is convenient to store pillows and blankets in it during the day and a cape at night.Assemble a nice decorative back and nail to the wall above the headboard. Place night lights on it.

This will give your bed an aristocratic chic and comfort.

Choose the material and decide on the price

Metal is too expensive, requires a specially equipped workshop, a welding machine, has a large specific gravity and does not retain heat well. Good furniture can be assembled at home from affordable lumber without overpaying for a well-known brand.

Building a wooden bed with your own hands will be cheaper than buying a finished one in a store.

How to make a bed out of wood with your own hands

Best for bed wood of medium (from 550 to 760 kg / m³) and high density - over 760 kg / m³. It wears out less, but is more difficult to process.

Pine is optimal in terms of strength and ease of processing.

IMPORTANT! Spruce is not suitable for load-bearing elements and legs of the bed ... It quickly collapses from stress.

For the supporting frame, select boards or solid timber - larch, birch. The legs can be made of bars, and the slats for the mattress are made of cheap pine boards 2 cm thick. Thin spruce boards 0.5 cm. Check the material carefully for knots, irregularities and roughness.

The fewer such defects are, the easier it is to process it with a grinder.

Check the curvature of the workpieces in a simple and effective way.

1. Raise it by one of the ends to eye level.
2. The ribs going from the near end to the far end should represent a straight line in perspective - their curvature will be noticeable immediately.

ATTENTION! Be sure to make a drawing. Consider the size of your mattress. They may not match the ones below. Inner space of the frame bed should be a little more. Allowed an allowance within 30 mm.

Decide immediately on the presence and height of the legs.

Bed solid wood can be made without them by gluing cloth pads at the corners to protect the floor from scratches. For light single beds and "one and a half" the optimal height will be 35-40 cm - you can vacuum and wash the floor or build a drawer for storing things and clothes.

ADVICE! Try to reinforce the joints with a furniture corner where possible.

Making a wooden bed with your own hands may not be the easiest solution, but the most profitable.

Entry level bed

Under a mattress with dimensions of 80x190 or 90x200 cm, build a simple single bed do-it-yourself bed made of wood ... It is suitable for an adult or teenager. For manufacturing you will need:

• B rus for four legs with a section of 50x50mm;
• D oska 25x245 mm for side boards and footboards, 25x100 mm - for the manufacture of overlapping slats, 25x200 mm- for the headboard wall;
• B rus with a section of 50x25mm for the manufacture of support beams for floor slats;

Materials for making the bed.

In addition to good lumber, purchase:

• Furniture corners or bed screeds.
• TO self-tapping screws 60 mm;
• Pins length 80 and a cross-sectional diameter of 8 mm;
• With roofing glue;
• M orilka or impregnation for wood;
• A krill water varnish.

Materials required for work.

During the assembly of this and other options bed use tools:

• D rail and screwdriver;
• H small hand plane;
• R circular saw or furniture hacksaw;
• NS bodice machine or sander;
• H a few clamps;
• TO sources for applying glue, varnish and stain;
• R sliding carpentry square;
• WITH building level;
• M alka - a device for quick marking of the cut corners;
• WITH tuslo - a tool for fast and accurate sawing of workpieces at an angle of 45 and 90 °;
• AND measuring tape.

Tools that will come in handy at work.

Assemble the headboard first. From a bar with a section of 50x50 mm, cut two legs up to 80 cm high. Drill 4-6 holes with a diameter of 8 mm and a depth of 30 mm in their upper part from the inner sides. Cut out two pieces of 950 mm wide from boards 25x200 mm. From the ends, make holes up to 50 mm deep, matching those that you made on the legs.

Lubricate the parts with wood glue at the joints and fasten with dowels, carefully hammering in with a mallet.

The foot is made from boards 25x240x950 mm and two pieces of timber 400 mm high.

Fasten them in the same way.

The backs are fastened to the side walls of 25x250x1900 mm with furniture corners or ties, aligned along the outer edge legs.

FOR YOUR INFORMATION! Ties will make it easy to disassemble furniture when moving.

Along the lower edge of the right and left walls, using wood glue and clamps, install support beams 25x50 mm and the length 190-200 cm. After drying, before removing the clamps, the beams are additionally screwed in with self-tapping screws.

Assembling the side wall of the bed.

From boards 25x100 mm, make 12-14 cross battens the length 95 cm. From the left and right ends, drill through holes with a diameter of 3 mm at a distance of 12 mm from the edge. Lay them across the support beams at a distance of 35-50 mm and tighten the self-tapping screws.

Final assembly of the bed.

IMPORTANT! All parts must be sanded before assembly. Use a sliding square to check the "straightness" of the corners between the side walls and backrests bed ... With a building level, control the horizontal arrangement of the frame structural elements.

Sand the rough surface with a sander. The outer ribs of the backrests and other parts can be chamfered to prevent wood chipping and improve appearance. To increase the service life, treat wood stain and dry. Cover with acrylic varnish.

As you can see, making a wooden single bed is not at all difficult.

FOR YOUR INFORMATION! So that the ends legs did not scratch the floor when moving, you can glue felt pads to them.

One and a half bed

There are differences in the design of the backs, and its longitudinal axis is reinforced with a lintel with a leg, which prevents the mattress from sagging.

It is made under a mattress with dimensions 140x200 cm.

The headboard of the lorry consists of a wall and two legs ... Make a wall from 2-3 boards the length 1400 mm and 25 mm thick, reaching the desired height (30-40 cm). The legs are made of 50x50x800 mm timber. Fastening wall elements and legs It is made with sheet piles 8x80 mm, carpentry glue and reinforced with long self-tapping screws from 65 mm.

The foot is assembled in the same way.

Side boards of the bed - the half-lorries must be level with the lower boards of the backrests and have the same height.Redesign the backs for variety bed ... The middle wall board can be replaced with short vertical inserts from the same boards fastened with tongue and groove.

Corners can be cut at the outer edge of the top board.

To do this, with the help of a special tool - malki - they make markings with a pencil. Malka consists of a handle pressed to the edge boards , a narrow metal plate with a longitudinal cut, and a fastening bolt that allows you to fix the plate by specifying the desired angle and length of the cut. In this simple way, you quickly draw symmetrical cutting lines on the left and right ends. To prevent the hacksaw from moving off the line, press a wooden guide bar along the marking with clamps.

To give an interesting look to the bed, before varnishing, you can limit yourself to applying stain only to the surface of the legs and backs.

How to make a double bed out of wood

Two adults are serious weight, which requires a more thorough approach in the choice of material and assembly method. Make a solid wood sleeping bed.

A standard double mattress measuring 200 x 160 cm is taken as a basis.

You will need the following materials:

• B rusok 50x50 mm for legs and bed frame, 3x3 cm - for support beams for mattress slats;
• D oski 20x100 mm for transverse flooring under the mattress;
• M metal furniture corner with shelf width from 50 mm;
• With self-tapping screws 40 and 65 mm long.

Of the tools, you will need an electric jigsaw equipped with a file with large and widely spaced teeth.

First, we assemble the frame for bed with internal dimensions of 210x170 cm and a height of at least 15-20 cm. To do this, glue three or four pieces of timber together, tighten with clamps. After drying, we cut it in such a way as to get two blanks for the side boards the length 220 cm each and two for the backs - 180 cm each.

In the same way, we assemble a longitudinal lintel with a height of 10 cm and a length of 210 cm.

Apply a lock-type connection when assembling. To do this, on short workpieces using a jigsaw, cut out a recess, removing a segment from the middle the length 5 cm. On long side panels bed , leave a "thorn", sawing off at the top and bottom by 5 cm.

Apply glue to the grooves and thorns and connect them at right angles, checking with a sliding "square".

Attach the longitudinal lintel with additional support in the middle using a metal corner with a shelf width of 50 mm, aligning it with the lower edge of the frame. In the corners, attach the legs from a bar up to 40 cm high.Fasten with glue and self-tapping screws.

Secure the joints with clamps for strength.

For greater reliability, make legs bed from a thicker bar. To give them a graceful look, chamfer the inside at a 45 ° angle using a miter box. Don't overdo it - the footprint should be large enough to support a lot of weight. When installing the legs, use long countersunk head bolts with washers and wood glue.

Place triangular inserts at the bottom of each corner to prevent deformation of the structure.

Glue 3x3x210 cm timber beams along the long side walls.

Their top edge should be in the same plane with the top edge of the web.

Slats are made from 20x100 mm boards the length 170 cm.They are laid and fixed across the lintel and longitudinal support beams at intervals of 3 cm.

The first and last slats should adjoin the front and rear walls of the frame, the rest should be evenly distributed between them.

IMPORTANT! To prevent the slats from squeaking, make them 1 cm shorter than the inner width of the frame.

After completing the assembly, carefully sand the surface with a grinder or drill with a special nozzle using medium and fine-grained sandpaper.Cover with wood stain, and after drying - with water-based acrylic varnish in several layers.

For double bed you can make a wall headboard from 2-3 boards the length 25x100x1800 mm and 10-12 boards 25x100x450 mm. The first row that will contact the back will go short boards ... On the seamy side, it is necessary to equip hidden fasteners. At the appropriate places of the headboard, screw metal plates with self-tapping screws, the free lower edge of which will be inserted when hanging into the grooves of the tires.

The most reliable solution would be to fix the rails for wall cabinets with dowels on the wall - according to the number of short boards.

If you don't like a hard headboard, assemble it with upholstery from the following layers:

• D JV or plywood 1 cm;
• P orolon from 3 cm;
• In atin;
• O leopard fabric with an interesting pattern;

Cut a 45x180 cm base from a piece of plywood or chipboard.

Chamfer the ribs and sand thoroughly to avoid tearing upholstery and batting.

Cut out a blank of the same size and shape from expanded polystyrene or foam rubber. Place it on the chipboard and make some symmetrical holes for the decorative buttons. Measure and cut the batting and upholstery fabric to the shape of the blank with an allowance equal to the sum of the thicknesses of all blanks, multiplied by two.

Make sure the holes are symmetrical.

Use glue or a special spray to glue the foam rubber to the base. Spread the batting gently on the floor. Lay the chipboard blank on it.

Fold the hemmed down, starting from the bottom, and use a furniture stapler to nail to the chipboard.

Repeat this operation with the upholstery. To prevent the fabric from wrinkling, iron it and tighten it properly using the clamps screwed to the middle of the workpiece.

IMPORTANT! Don't skimp on staple staples. Nobody will see them anyway.

Finally, "sew on" the sofa buttons. From the seamy side of the headboard, pierce the upholstery with a large "boot" needle and pull through a thick coarse thread, thread it through the eye of the button and bring it back out through the same hole.

Secure the ends of the thread with a stapler on the wrong side of the back.

Hang the upholstered headboard on the wall using the wall cabinet rails.

A wooden bed with your own hands, made according to a personal project, will cost less than a purchased one.

Remember, the lack of extra money and the lack of living space are not an obstacle to the realization of the desire to sleep comfortably.

VIDEO: Do-it-yourself double bed made of wood.

In the modern market for goods and services, you can find absolutely everything, but many people prefer to make an interior item on their own, without resorting to the help of specialists. A do-it-yourself double bed, drawings and diagrams of which are attached, can become a real decoration of the bedroom interior. To make such a bed, you need to familiarize yourself with the general recommendations of specialists, make a drawing and a plan of sequential actions. The drawing is needed to calculate the necessary materials, funds for their purchase and drawing up a sequence of installation work.

Preparatory work

A do-it-yourself double bed has a number of advantages - it is the ability to choose the required size, design, shape of the legs, as well as the quality of the finished product in the end result, thanks to which the bedroom turns into a masterpiece.

The main details in its manufacture are:

• design, which can be classic or with a lifting system;
• a drawing that helps in the preparation and manufacture of parts;
• sequential action plan.

Double bed layout with mattress

Drawings and diagrams

Not a single work on the manufacture of interior items is complete without drawings and diagrams. The manufacture of a double design was no exception. Below you can see several options for drawings and diagrams often used in the manufacture of double models.

Having decided on the type and size of the double bed, you need to make a detailed drawing. The scheme allows you to buy the required amount of building materials of a certain size or order their production in a furniture workshop. The drawing is also used throughout the entire construction process, for the manufacture of individual elements with your own hands and their fasteners.

Double bed with several drawers
Assembly diagram
Bed with two drawers on the sides

Basic details

Beds with side tables

Side view
Assembling the frame

Materials and tools for work

The double bed can be regular or with a lifting mechanism. The technique of making them is slightly different from each other, since the product with a lifting mechanism has an additional box for storing things and a lifting frame for a berth.In order to determine the size of the product, you need to take into account the size of the factory mattress that you plan to purchase.To make a standard double bed with your own hands, you will need such materials.

When choosing a material, many are faced with wood of different qualities. Experts recommend choosing high quality wood only for the supporting structure. Second-class material is available for the legs and bottom rails. If there is not enough money for high-quality material, you can buy chipboard or plywood.

If you plan to make a product with a lifting mechanism, then a little more materials will be required. Since, in addition to the main frame, it is also necessary to make a lifting frame for a berth. For its manufacture, you can use metal building material. The drawing should include not only the building material, but also the type of the lifting mechanism, because its installation plays an important role.

Choosing a board

Tools that will be required:

• roulette;
• pencil or marker;
• brushes;
• sandpaper;
• wood putty;
• varnish, stain;
• glue for wood;
• self-tapping screws (30, 50, 60 mm);
• measuring square;
• drill;
• jigsaw;
• clamps;
• grinding machine;
• construction stapler;
• hacksaw.

When cutting parts according to the dimensions of the drawing, you need to mark them as accurately as possible.

Main frame

The process of making a double bed with your own hands begins with the main frame. A product with a lifting mechanism is also made from its base, which consists not only of four boards, but also of the bottom, as in the photo.

Assembling the frame

Stages of frame manufacturing:

• in the prepared parts, it is necessary to make holes for fasteners with a drill. The diameter should correspond to the 30 mm self-tapping screws that are used to fasten the boards;

We prepare holes for fastening

• clean the ends of the boards with sandpaper or a grinder;

We clean the ends of the boards with a grinder

• open them with wood glue;
• insert self-tapping screws into the drilled holes, fasten the boards with a screwdriver or screwdriver;

We fasten the boards with self-tapping screws

• after finishing bonding, you need to remove all excess glue with a damp cloth;

Remove excess glue with a damp cloth

• at the end, it is necessary to check all the corners of the structure, make sure that they are straight, using a construction square;
• after the frame dries, you need to paint it. The color of the stain is chosen solely from the personal preferences of the owner;

Finished frame after painting

• if the frame is made in the form of a box, it is necessary to make the bottom, which can be solid (made of plywood) or rack and pinion.

Fastening the supports for the rack bottom

The batten supports are attached in the same way as the frame.

Rack bottom support technology:

• in the support boards, it is necessary to drill holes for the thickness of the screws, in increments of 25 cm;
• for fixing the boards, it is better to put the frame on its side and having drawn a line at a distance of 5 cm from its bottom, you can proceed to the installation steps;

I put the frame on its side for fixing the boards

• before fixing the support boards, they must be greased with wood glue;
• fastening along the frame along its edges, using self-tapping screws 50 mm;
• for stability during the drying of the glue, the support block must be pressed, for this you can use clamps. An example can be seen in the photo;

The frame with the bar was fixed until completely dry.

• the middle support board is fixed parallel to the two previous ones, at the same height, by drilling holes in its ends;
• the remaining holes from the fasteners must be sealed with putty and cleaned with sandpaper after it dries.

Legs

Making legs with your own hands is the simplest step in the entire construction process.

The whole manufacturing process:

• a prepared timber with a section of 10x10 cm needs to be cut into 6 bars 10.5 cm long;

Preparation for future legs

• fastening is made to support bars;
• for the strength of the frame, two additional legs are attached under the central support, at a distance of 50 cm from the edges of the frame;
• for their decoration, you can give them any shape. You can saw off one of the corners about 3 cm from the bottom, at an angle of 45 degrees, as in the photo;
• at the end of the work, all sides must be sanded.

Fastening all created elements:

• as mentioned above, the legs are attached to the support boards of the frame. To do this, you must use self-tapping screws 60 mm. You need to spend at least two for each leg;

It looks like the attachment of the legs from the inside

• holes are pre-drilled with a drill, a drill, the diameter of which coincides with the section of the self-tapping screws.

Legs attached to the frame

Before screwing in the self-tapping screws, you must first drill the holes, thereby reducing the risk of splitting the boards.

Decorative elements

Decorative elements play an important role in finishing the product; thanks to them, the bedroom will sparkle with new colors. One of the options for finishing elements are wooden slats, 5 by 2.5 cm thick, which should also be included in the drawing.

Manufacturing process:

• it is necessary to make the required size of the slats from the prepared materials;
• prepared slats must be sanded, painted with a stain, the color of which is chosen from personal preferences and the design of the room;
• after drying, they are covered with water-based varnish;
• after opening the first layer of varnish, you need to polish the slats from the appearance of all kinds of bubbles. Next, apply two more coats of varnish;
• the painting procedure must also be carried out with the legs.

Fastening:

• decorative trim is attached with glue;
• it is necessary to apply glue to the surface of the frame and finishing strips;
• with the help of clamps, press them for a while, preferably until the glue is completely dry;
• all excess glue must be wiped with a damp cloth;
• the fastening of the rails can be done both with nails and with self-tapping screws.

Fastening the lifting mechanism requires additional skills, since its installation must be of high quality and safe. There are three types of mechanism, the installation of each of which occurs in a different way. Therefore, having chosen a certain type, you need to carefully study the scheme of its installation or resort to the help of specialists.

Reiki

For making classic beds with your own hands, the slats are placed on the support boards of the frame. And in products with a lifting mechanism, they fit on a lifting frame. Or it is possible to lay them on two frames at the same time, since on the frame they are used for the bottom, and on the lifting frame, for laying the mattress.

Reiki is made very simply:

• according to the specified dimensions, it is necessary to measure the length of the slats and saw off from the purchased boards;

Layout of boards for the manufacture of slats

• for convenience and practicality, so that there are no discrepancies in the length of the battens, the first strip can be used as a sample, and subsequent boards can be marked on its basis;
• having finished the process of making the rails, you need to grind each one.

How to make a headboard and what is needed for this

A headboard in a double bed is needed for three main reasons:

• it is a decorative element;
• protects the wall covering from rubbing;
• for convenience.

The headboard can be of different sizes, shapes and coverings, it all depends on personal preferences, the interior of the room and financial capabilities. Here is a photo of some examples.

Before making it, you also need to make a drawing with your own hands, which will indicate the dimensions and necessary materials. Mainly used plywood sheet, upholstery fabric and foam, to create a soft and airy headboard.

Complete manufacturing technology:

• the first thing to do is to measure the width and height of the headboard. Transfer all dimensions to a plywood sheet and cut out details;

Cut the foam rubber according to the size of the workpiece

• if the rectangular shape of the headboard does not suit you, you can make it round or ornate. To do this, prepare a piece and a jigsaw in advance;
• irregularities and notches resulting from the sawing process must be treated with sandpaper;
• to make a soft headboard, you will need foam rubber, a stapler and upholstery fabric. Attach the foam rubber to the headboard blank with a stapler and cover with prepared fabric;

Foam rubber must be attached with a stapler and covered with an upholstery fabric

• if you plan to make an ordinary headboard, then the plywood blank must be opened with varnish or paint;
• the finished headboard can be attached directly to the sleeping area or to the wall.

The bedroom should create an atmosphere of warmth and comfort, which is achieved through design and furniture attributes. A good bed is needed not only to decorate a room, but also to ensure a sound, comfortable sleep, which can be achieved with the right bed. You can not only purchase it, but also do it yourself. Having fulfilled all the requirements, the product will serve for a long time, performing all its intended functions.

Today, many are concerned about the ecology of the home, including health-friendly furniture made from natural materials. This is most important for the furniture in the bedroom, and especially for the bed, on which a person spends a third of his life, rests, and is charged with energy for active work. Of course, beds made of natural wood can also be bought in a store, but such furniture is very expensive, and it can be problematic to find the model that is necessary in size, shape, color. Therefore, for many, the question arises of making a wooden bed with their own hands. It is not difficult to do this, but the product will suit your requirements and will cost much less, because you will have to pay only for the materials.

Consider making the simplest model of a wooden double bed.

Required materials and tools

The amount of materials needed to make a bed depends on its size. But before drawing up a drawing and determining the length and width of the bed, you need to know the exact dimensions of the mattress. Purchased mattresses usually have standard sizes. If for some reason this does not suit you, you can make the mattress yourself from two layers of foam rubber with a thickness of 125 mm: the lower layer is less dense (35 kg / m 3), the upper one is more dense (at least 45 kg / m 3). In this case, you can take the length and width of the foam rubber that suits you. For example, 200 cm and 150 cm. A mattress topper that is sewn to size is put on the finished layers. Thus, the mattress will have the following dimensions: length 200 cm, width 150 cm, height 25 cm.

For a bed of this size, you will need the following materials:

• boards 250x30x2 cm for side walls - 2 pieces;
• boards 200x30x2 cm for the front, back walls and headboard - 3 pieces;
• timber 200 × 4x4 cm for four carriers, support and legs - 5 pieces;
• lath 150 × 4x2 cm for lathing and fixing headboard boards - 25 + 2 pieces (can be replaced with thick plywood);
• self-tapping screws;
• joiner's glue;
• varnish, stain.

Bed plan - clickable

You can't do without the appropriate tools:

• screwdriver;
• drill;
• jigsaw;
• cutter;
• hacksaw;
• plane;
• sandpaper;
• measuring instruments - tape measure, metal ruler, square;
• pencil.

Having prepared the tools and purchasing the necessary materials, you can start marking and sawing lumber. In this case, it is worth following a few rules:

• first you need to make a drawing of the bed, indicating on it the exact dimensions of all parts; then it is advisable to make a list of these parts and the amount of material for them;
• the line along which the cut will be made must be marked with a cutter or pencil along a ruler;
• when making several parts of the same type and size, first cut out one part, and then use it as a template;
• the surface of the saw cut must be cleaned with sandpaper.

Wooden bed manufacturing technology

Determine the location for the support bars on the front and rear wall. To do this, divide the length of the walls into three equal parts and make the appropriate markings. The depth of the mattress is 5 cm. Add to this figure the thickness of the slats (2 cm) and supporting longitudinal beams (4 cm). It turns out 11 cm, which you measure from the top of the walls in the marking places.

Screw on the two support bars from the inside. When choosing self-tapping screws, take into account the thickness of the bars and boards so as not to spoil the front surface of the product.

Screw the support bars to the side walls. To do this, measure 7 cm from the top of the board (the thickness of the slats and the depth of the mattress) and draw a line with a ruler. The support bars are screwed along the entire length of the side wall, retreating from the edges by 6 cm.Around the edges of the support bar, screw two vertical pieces of a 4 cm thick bar so that the indent to the edge of the board is strictly 2 cm.

Attach an additional headboard to the front wall. Pre-coat the edges with glue and align the workpieces perfectly. From the outside, reinforce the headboard with three slats, which are glued and screwed on with self-tapping screws. You can choose the shape of the headboard to your liking.

Cover all blanks with stain, achieving the desired color. Then apply the quick-drying varnish twice.
Assemble the bed frame by connecting the blanks to each other with self-tapping screws.

Place two support beams on the support bars of the rear and front walls and screw them with self-tapping screws. For better support, two legs with a height equal to the height of the side walls can be screwed to the load-bearing beams in the middle.

Lay the slats (or plywood, depending on the option) on the supporting structure, maintaining a distance of 4 cm between them and 2 cm away from the front and rear walls. Screw the slats with self-tapping screws. Place the mattress on the finished bed.

The result is a classic wooden bed that is very durable, eco-friendly, and fits in with your bedroom interior. If there is a desire and certain skills, you can decorate the structure with various decorative elements.

Plan and photos from Serjant (guns.ru forum)